New Generation Of Optical Micrometers Provide More Accurate Measurement Of Surface Defects On Critical Parts
By Jim McMahon
High-brightness LEDs with fiber optics, CCD array sensors, archiving of defect images and data, and real-time PC graphic-user interface are some of the latest features being designed into next-generation hand-held optical micrometers - used to determine the severity of damage caused to critical parts from scratches, blemishes and corrosion pits.
J. Chadwick Company, with electro-optics design from Lincoln Laser Company, are leading the way with the latest advanced-technology, new-generation systems.
Whether it is scratches on a helicopter's rotor blades or on the fuselage skin of an aircraft, or corrosion pitting on industrial couplings, castings, transmissions or engines, it is critical to evaluate the severity of mechanical damage to stress-bearing parts. These surface defects represent stress concentrations which are more susceptible to failure than the other areas of the component.
Very specific maximum allowances often apply to surface defects, which are essential to determine whether or not a part should be kept in service. To repair or replace the part can have significant structural and financial impact. For example, a helicopter's mast, which connects the chopper's motor to the main rotor, has a defect depth allowance of .012 to .015 of an inch.
If the depth of the defect exceeds those parameters, then it is at risk of breaking and must be replaced. But replacing parts can be a very expensive proposition. In the case of helicopters, masts can cost as much as $25,000 to replace.
Careful visual inspection should, therefore, be standard protocol for any force-absorbing component that exhibits scratches, blemishes or corrosion pits.
Hand-Held Optical Micrometers
The portable optical micrometer has long been the tool of choice to measure the depth of these defects, from the surface to the bottom of the depression, thereby determining the severity of mechanical damage.
Optical micrometers are portable microscopes specifically designed for measuring depth. They are used for measuring three-dimensional relief along the z-axis within any x-y field of view, and they accomplish this by measuring the difference in depth between any two focal planes. The instrument is focused on a region of interest and set to zero. Then as a second region is brought into focus, depth is shown on a digital display. Optical micrometers serve as non-contact height gages and are ideal for small or intricate subject matter. This simple and practical capability has countless applications in almost every area of science, manufacturing, aerospace, quality control, and industry.
As an inspection tool, optical micrometers are simply outstanding - providing quick, accurate and repeatable results where other methods are time-consuming and inconclusive. Scratches, gouges and corrosion pits are easily measured where the fingernail-test is often the only alternate method in use.
Aviation and aerospace components have maximum allowable scratch depth limits. From windshields and landing gear, to fuselage skin and engine parts, optical micrometers are used to measure defects. A helicopter's mast that supports the main rotor, for example, may have a maximum allowed scratch depth of .015 of an inch. Repair-or-replace decisions here can affect safety and have financial impact.
Optical micrometers bring precision and integrity to this judgment process - especially where the fingernail-test is the only alternate method in use. If a component is scratched too deeply, time and money are saved by making quick and sure decisions, and even more money is saved by not scrapping parts that are well within tolerance. It is to everyone's advantage when the guesswork is removed from decisions regarding aircraft component integrity.
From incoming raw materials to finished parts, optical micrometers routinely measure surface flaws, scratches and corrosion. Both vendors and buyers improve their process controls by agreeing on what constitutes a reject versus an acceptable blemish whenever cosmetic value is a requirement.
Optical micrometers are particularly good for measuring the depth of corrosion pits, as built-in magnification makes it easy to find the deepest part within a given area. Hours of blend-out labor can be avoided when it is determined ahead of time that a corrosion pit is too deep.
Optical micrometers are also used to check dimensional accuracy, like calipers and other workshop and quality control measuring equipment, in manufacturing and production environments. Serving as non-contact height gages, they can confirm the height of a component above a background or substrate on a micro-circuit or assembly, measure the depth of tiny steps, layers and grooves, or the actual depth of small mold cavities, for example.
Introduced in the 1950's, optical micrometers hold several NSN's (National Stock Numbers), they are in the supply systems of several corporations and are used on the Space Shuttle and International Space Station.
Whether they are used to check dimensional accuracy or to measure the severity of flaws and defects, optical micrometers are compared to N.I.S.T. (National Institute of Standards and Technology) traceable standards and required to be re-certified on a regular basis just like other quality-control measuring equipment.
New Generation of Portable Optical Micrometers There have been major product improvements and upgrades with portable micrometers over the years, but none that compare to the completely new and innovative designs of the latest models. The most prominent example being the newly re-designed portable optical micrometer by the J. Chadwick Company (Chadwick), who teamed up with Lincoln Laser Company (Lincoln) to collaborate on the design and manufacturing for a new-generation, electronic version of portable micrometer. Chadwick is an OEM of portable optical micrometers, having manufactured analog and digital versions for the military and the aerospace industry since the early 1990's. Lincoln Laser specializes in the design, engineering and manufacturing of high-precision mechanical, laser-based, and electro-optical systems.
Chadwick's latest version of hand-held micrometer, called the Depth Cam, was designed to handle resolutions as low as one micron, and offer a number of electronic capabilities that have not been available in prior portable micrometers. The intent was to build an instrument that was easier and faster to use, produce consistent detailed and accurate results, interface with a PC for real-time control and monitoring, and have the capability to store data for later evaluation and comparison.
"Portable optical micrometers needed to bring a higher level of precision and integrity to this important judgment process," says John Chadwick, President of the J.Chadwick Company. "Should a defected part be repaired or replaced? An instrument that is giving inaccurate readings could cost a company many thousands of dollars in unnecessary new parts when the defective ones were still within compliance."
The system is the first camera- and PC-based portable optical micrometer. Once the micrometer is positioned over a point of interest, the user does not look through a lens as in prior portable micrometers, but instead controls the movement of the objective through a portable PC, by operating a mouse while viewing a monitor, or graphic user interface (GUI).
The optical micrometer has a microscope objective with a CCD array sensor positioned above it, having a resolution of 1280 x 1024 pixels. A light is shined at the surface of the part being viewed and the array registers its position. The light is emitted from high-performance LEDs and channeled via fiber optics to the point of interest. The micrometer then will zero-out a linear scale, and the operator selects the bottom of the defect. The light is shined on that point of interest and it is recorded on the CCD sensors.
The color USB 2.0 camera and illumination from the high-brightness LED's are individually adjustable from a laptop. A one-micron linear encoder provides high resolution, and a rechargeable lithium-polymer battery pack supplies power. A motorized focus is operated remotely from a laptop or by a rotary dial with five-way toggle on the instrument. Focus can run in velocity or position mode, and at different speeds and increments within each mode.
The system provides live image preview with real-time camera and focus controls, image capture, video, and zoom. Custom GUI buttons line the borders of the live image, and current depth value is always displayed, and can be set or reset to zero at any position within the range of travel. Two region-of-interest boxes can be drawn via click and drag, for surface-A and surface-B selection, and focus metering optimizes focus within each region-of-interest box.
Images can also be archived for future reference. This allows comparatives to be made with prior measurements of the same part, or similar parts to aid in evaluation.
"Chadwick brought us in to take the hand-help optical micrometer to the next level, to make an electronic rather than a manual device," says Alex Biegel, Mechanical Engineer with Lincoln Laser. "We designed the electro-optics, software and graphics for the unit. The engineering certainly had its challenges, designing the unit to have a scratch depth measuring capability to 20,000ths of an inch, and operating at the one-micron level."
"The whole unit was modeled in 3D," continues Biegel. "That allowed us to figure out our three-dimensional packaging very accurately. We would also be manufacturing the instrument, so this ensured we would not encounter manufacturing problems later on down the line. It makes any updates, upgrades and further engineering much easier."
Portable Micrometers with 3D Solid-Modeling on the Horizon In the near future, 3D solid-modeling is possible. Multiple images from different focal planes form a virtual solid which can be viewed from any angle by rotating with a mouse on-screen.
Depth-of-field will be addressed by image fusion, where images from different focal planes can be combined into one all-in-focus picture, and videotext overlays will allow text, arrows and calibrated scales to be drawn onto images.
Image analysis will allow nodularity and porosity classification, plating thickness measurement and grayscale thresholding.
Whatever tech improvements are on the horizon for portable optical micrometers, it is clear that the instrument has just recently taken a quantum leap forward in accuracy and user flexibility.
About Lincoln Laser Company
Lincoln Laser Company is an engineering and manufacturing company that specializes in custom-built, high-precision laser systems, laser scanning components and electro-optic subsystems. Lincoln services a global clientele of OEMs and works closely with its clients to bring their new product ideas to market. Over the last 30 years, the company has developed many unique components and systems for its customers such as high-speed laser printers, package handling and inspection devices, food inspection systems, medical imaging devices, retinal scanning systems, dermatology systems, barcode scanners, warehouse inventory devices and other specifically-tailored scanning processes.
Lincoln sets the standard in the optics industry with its flexibility in product design, specification changes, production volumes, delivery requirements and re-manufactured products. Its five-building, three-acre campus with 50,000 square feet of manufacturing and office facility, provide Class 1000 clean rooms, soft wall clean rooms, a thin-film coating laboratory, a nickel plating laboratory, a complete machine shop with CNC lathes and mills, hones and grinders, a diamond turning machine center, optical fabrication - lapping and polishing, and precision assembly and custom testing. Lincoln Laser provides contract manufacturing of electro-optics modules, from re-design and upgrade of existing equipment, to complete turnkey system design and manufacturing. For more information, visit www.lincolnlaser.com.
SOURCE: Lincoln Laser Company